Detailed Product Description
CNC stepper motor driver kit
Input: 24--58VDC;
Output: 1.4--5.6A;
Microstep: 2-128; 5--125
CNC stepper motor driver kit
Key Features:
24 to CNC stepper motor driver kit 50VDC Supply Voltage
H-Bridge, 2 Phase Bi-polar Micro-stepping Drive
Suitable for 2-phase, 4, 6 and 8 leads step motors, with NEMA size 16 to 34
Output current selectable from 1.4 ~ 5.6A peak
Current reduction by 50% automatically, when motor standstill mode is enabled
Pulse Input frequency up to 200 kHz
Optically isolated differential TTL inputs for Pulse, Direction and Enable signal inputs
Selectable resolutions up to 12800 steps
Over Voltage, Coil to Coil and Coil to Ground short circuit protection.
Introduction
2M656 is a cost effective, high performance bi-polar two phase micro-stepping drive applying pure-sinusoidal current control technique. It is best suited for the applications that desired extreme low noise and heat. It operates well in an environment, where electricity supply experience instability and fluctuation.
The general pseudo-sinusoidal current control technology adopted by majority of the drive produced distorted sine wave, and current ripple, resulting in vibration, noise and motor heating. This results in motor degrading over time, reducing in motor performance and shortens the usage life.
With an automatic optimization speed control technique, the PowerStep series drive output is very stable, with almost zero vibration and noise, performing close to a servo system, allowing the motor to operate smoothly. That helps to fulfill a design requirement of low noise, low heat and high performance.
CNC stepper motor driver kit
Input: 24--58VDC;
Output: 1.4--5.6A;
Microstep: 2-128; 5--125
CNC stepper motor driver kit
Key Features:
24 to CNC stepper motor driver kit 50VDC Supply Voltage
H-Bridge, 2 Phase Bi-polar Micro-stepping Drive
Suitable for 2-phase, 4, 6 and 8 leads step motors, with NEMA size 16 to 34
Output current selectable from 1.4 ~ 5.6A peak
Current reduction by 50% automatically, when motor standstill mode is enabled
Pulse Input frequency up to 200 kHz
Optically isolated differential TTL inputs for Pulse, Direction and Enable signal inputs
Selectable resolutions up to 12800 steps
Over Voltage, Coil to Coil and Coil to Ground short circuit protection.
Introduction
2M656 is a cost effective, high performance bi-polar two phase micro-stepping drive applying pure-sinusoidal current control technique. It is best suited for the applications that desired extreme low noise and heat. It operates well in an environment, where electricity supply experience instability and fluctuation.
The general pseudo-sinusoidal current control technology adopted by majority of the drive produced distorted sine wave, and current ripple, resulting in vibration, noise and motor heating. This results in motor degrading over time, reducing in motor performance and shortens the usage life.
With an automatic optimization speed control technique, the PowerStep series drive output is very stable, with almost zero vibration and noise, performing close to a servo system, allowing the motor to operate smoothly. That helps to fulfill a design requirement of low noise, low heat and high performance.
|
Cooling |
Natural Cooling or Forced Convection |
|
|
Environment |
Space |
Avoid dust, oil frost and corrosive gases |
|
Ambient Temperature |
0°C50°C |
|
|
Humidity |
40 80%RH |
|
|
Vibration |
5.9m/s² Max |
|
|
Storage Temp. |
-10°C 80°C |
|
|
Weight |
Approx. 260 gram |
|
Microstep Setting
|
Step / Rev |
SW5 |
SW6 |
SW7 |
SW8 |
|
200 |
OFF |
OFF |
OFF |
OFF |
|
400 |
ON |
OFF |
OFF |
OFF |
|
500 |
OFF |
ON |
OFF |
OFF |
|
800 |
ON |
ON |
OFF |
OFF |
|
1000 |
OFF |
OFF |
ON |
OFF |
|
1250 |
ON |
OFF |
ON |
OFF |
|
1600 |
OFF |
ON |
ON |
OFF |
|
2000 |
ON |
ON |
ON |
OFF |
|
2500 |
OFF |
OFF |
OFF |
ON |
|
3200 |
ON |
OFF |
OFF |
ON |
|
4000 |
OFF |
ON |
OFF |
ON |
|
5000 |
ON |
ON |
OFF |
ON |
|
6400 |
OFF |
OFF |
ON |
ON |
|
8000 |
ON |
OFF |
ON |
ON |
|
10000 |
OFF |
ON |
ON |
ON |
|
12800 |
ON |
ON |
ON |
ON |
